SAL Electronics Products

All SAL Electronic wire antennas are Made in the USA.

SE-2M 2 Meter Moxon

SE-EF8010, 80 to 10 Meter 43 ft End Fed antenna

The SE-VUGP is a Heavy-Duty Ground Plane equipped with a 150 Watt dual band gain antenna for either a permanent or temporary fixed station antenna installation. Antenna gain is 2 dBq for VHF, and 5 dBq for UHF. The radials are bent to a 45^o angle to preserve a 50 ohm match, and are made of 3/8" O.D. 6063-T832 aircraft quality tubing. The far ends are capped with a vinyl foot to keep out moisture and also provide a soft footing if used on a table indoors for a temporary installation. The mounting ends are filled with fiberglass to seal against moisture and to provide additional mounting strength. The mounting plate is machined from a one piece 0.09" 6061-T6 aircraft quality aluminum plate. The mounting clamp is 3/8" zinc plated steel for maximum strength and ware. The SE-VUGP is made to outlast many fixed antennas on the market. Your investment will last for many, many years. Available with your choice of UHF or Type-N Connector at no extra cost. Click here for more information.

The SE-2MGP is a Heavy-Duty Ground Plane fitted with a 3dBq 5/8 wave radiator using a 3/8"-24 stud for a permanent or temporary fixed station antenna. The antenna is rated for 500 Watts continuous (FM Mode) operation. The radials are bent to a 45^o angle to preserve a 50 ohm match, and are made of 3/8" O.D. 6063-T832 aircraft quality tubing. The far ends are capped with a vinyl foot to keep out moisture and also provide a soft footing if used on a table indoors for a temporary installation. The mounting ends are filled with fiberglass to seal against moisture and to provide additional mounting strength. The mounting plate is machined from a one piece 0.09" 6061-T6 aircraft quality aluminum plate. The mounting clamp is 3/8" zinc plated steel for maximum strength and ware. All mounting screws are 18-8 stanless steel. The SE-2MGP is made to outlast many fixed antennas on the market. Your investment will last for many, many years. Click here for more information.

The SE-OCF806, 135 ft overall (40.7 Meter) Off-Center-Fed (OCF) "Windom" style Antenna. Install as a conventional straight horizontal dipole, Inverted "V", or sloper. Covers 80 Meters to 6 Meters using a heavy-duty 4:1 current balun providing full 40, 20, 17, 12, and 10 meter operation without an antenna tuner (external tuner required for 60, 30, and 15 Meter bands at 200 Watts maximum). Other features are a low noise reception direct DC ground construction and built-in RF choke design. All stainless steel hardware, and hard to see #14 Black nylon coated wire. All you need to supply are coax and mounting rope. To help facilitate installation the short side is marked by the end insulator.

Click here for more information.

The SE-EF1606, 90 ft (27.4 Meter) non-resonant End Fed Antenna. Use where a dipole arrangement is impractical. The EF1606 can be installed as a horizontal "V", a "U", or as a Delta or Square horizontal loop for a more omni-directional pattern. Of course the EF1606 can be installed in the conventional straight line, or as an End Fed Inverted "V". Since the SE-EF1606 is a non-resonant length wire, it requires an external antenna tuner to provide total 160 Meter to 6 Meter coverage. Other features are low noise reception direct DC ground construction, and no RF in the shack. All stainless steel hardware, and a hard to see #14 Black PVC coated wire. All you need to supply are coax and mounting rope.

Click here for more information.

SAL Electronics is proud to supply you with the finest heavy-duty wire antennas. Several of the wire antennas do not require an antenna tuner for several bands. The VHF and UHF antennas use aircraft quality materials to provide long lasting, trouble-free usage. All of our products are made in the U.S.A, and are built tough. SAL Electronics, LLC reserves the right to make technical alterations without prior notice.

Products

To SE-OCF806

To SE-2MGP

To SE-VUGP

SAL Electronics LLC

Algonquin, IL 60102

Phone: (815) 669-6567

To Accessories

SAL Electronics provides several accessories to enhance your communications. Items included are whip antennas, connector adaptors, and NMO style add-ons. Click here to access the Accessories Page for more information.

SE-EF1606 Multiband End Fed Antenna

SE-OCF806 Multiband Dipole Antenna

SE-2MGP 3 dBq 5/8 wave Ground Plane

The SE-BRACKET is a mounting plate for any mid or high power End Fed Antenna or the Off-Center-Fed Antenna. The bracket allows for mounting the match box of these antennas to a vertical or horizontal mast. Zinc plated steel clamps allow for mounting to a maximum 2" OD pipe or other supporting structure where a hanging mounting method is not available. The mounting plate is made from 1/8" thick heavy aircraft quality aluminum for years of trouble-free installation.

Click here for more information.

To: SE-BRACKET

SE-BRACKET, Mast mount adaptor for SE-EF135/OCF135

The SE-EF4010, 45 ft (14 Meter) End Fed Antenna. Use where a dipole arrangement is impractical. The SE-EF-4010 is a low power unit designed for 100 Watts PEP or less, and can be used as an attic antenna or for portable operation. The SE-EF4010 can also be used as an effective SWL antenna for RX operatiopn between 1 MHz and 108 MHz. The SE-EF4010 can be installed most effectively as a horizontal "V", a "U", or as a 15 Meter Delta or Square horizontal loop for a more omni-directional pattern. Of course the SE-EF4010 can be installed in the conventional straight line, or as an End Fed Inverted "V". The SE-EF4010 requires an external antenna tuner to provide 40 Meter to 10 Meter coverage. The EF4010 does not require radials when installed with coax cable, grounded at the point of entry. Other features are low noise reception direct DC ground construction, and no RF in the shack. All stainless steel hardware, and a hard to see #14 Black PVC coated wire. All you need to supply are coax and mounting rope. Click here for more information.

The SE-EF8010, 43 ft (13 Meter) End Fed Antenna. Use where a dipole arrangement is impractical. The SE-EF8010 is a mid power unit designed for 500 Watts PEP or less, and can be used for portable operation. The SE-EF8010 can be installed as a horizontal "V", a "U", or as a Meter Delta or Square horizontal loop for a more omni-directional pattern. Of course the SE-EF8010 can be installed in the conventional straight line, or as an End Fed Inverted "V". The SE-EF8010 requires an external antenna tuner to provide 80 Meter to 10 Meter coverage.The SE-EF8010 may be used without a tuner on 40, 20, and lower portion of the 10 meter band. Other features are low noise reception direct DC ground construction, and no RF in the shack. All stainless steel hardware, and a hard to see #14 Black PVC coated wire. All you need to supply are coax and mounting rope.

Click here for more information.

The SE-2M is a wideband Heavy-Duty Moxon antenna for the 2 Meter Band. Less than 1.5:1 VSWR from 144 MHz to 148 MHz (usable with less than 1.8:1 VSWR from 141.5 MHz to 151.5 MHz) provides great operation across the entire 2 Meter Ham Band without tuning, plus will accept CAP operation as well. Well suited for VHF rover operation, the SE-2M offers great fixed staion operation using either Horizontal or Vertical polarization. The supplied 1:1 ferrite balun provides direct DC ground and full balanced operation (no pattern distortion). Rated at 500 Watts PEP, and able to survive 120 MPH winds with 1/2" radial ice, this antenna can take it. Built of aircraft quality aluminum, UV resistant PVC, fiberglass, and stainless steel hardware. Antenna elements are made from 6063-T832 hard drawn aluminum tubing, measuring 28.75" W x 11.5" D. Standard termination is the SO-239 UHF female, with a no charge Type-N female connector available as an option. Ask about the optional phasing harness kits that provide additional gain when two or more Moxon's are used. Click here for more information.

To SE-2M